Tips On How To Extend Smok Pen Recharge Time

Tips On How To Extend Smok Pen Recharge Time

smok pen

Tips On How To Extend Smok Pen Recharge Time

The Smok Pen is a new pen that was created by two guys in California. They wished to create a cool writing instrument that looked like a genuine pen but had the ability to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has had the marketplace by storm.

The Smok Pen has a built quality that’s just great. I found that even though it can be an electronic pen the build quality is simply as good as any of the pens that I’ve reviewed. It is because of how they made the top cap. You don’t have to be worried about the cap cracking or breaking you Smok Valve Pen.

The two biggest differences that separate the Smok Valve from other pens may be the shape of the coils and just how that they are built. In general the coil on a Smok Pen is bigger than on other pens. I believe that they did this deliberately, to make the pen feel more substantial.

vapinger.com If you take a glance at a Smok Pen, you will notice that your body of the pen is round rather than smooth like other pens. On the trunk of the pen there is a little tab that houses the coil. When you press on the tab you can actually turn the heating element on and off. I must say i liked this feature because it allows me to use the Smok Pen 22 whenever I feel like smoking.

To utilize the Smok Pen you should keep carefully the heat button pressed. Once the button is pressed, the heating element will start to warm up. Once it reaches the appropriate temperature you can turn off the heating element. Smok recommends using a 22mm tank. I prefer a larger tank, but that’s just me.

Once you put your Smok Pen into the tank you will notice a indicator light seriously. The indicator light will stay green if you don’t put your Smok Pen in to the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. You should always put your pen into the charger before you apply the e-liquids to the coil heads. It is also important to do this before putting your e-liquids into the coil heads.

After you have completed this step, it is best to check to see when you are at the right temperature for the coils to fire. Or even then you should turn the power off and try again. For anyone who is still not satisfied with your Smok Pen then I suggest you take it in for some troubleshooting. This is what I’d call the “troubleshooting process” because sometimes things just do not work as they should. I would recommend that you perform the following two steps, then go ahead and check the Smok Pen to see if it still gets the electronic charging port.

Before you go any further you should take away the battery from your own pen and unscrew the magnetic cap. You need to then take away the plastic sleeve that holds the sub-ohm. You will find a wire that runs through the Smok’s body that is green in color. You should loosen this wire using pliers. After you have loosened this wire you can then access the sub-ohm. You need to then remove the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful never to touch any of the coils.

When you have placed the sub-ohm tank into the pen you need to then place all of those other components including the wattage, the batteries and the heating element in to the included microwaveable microwave oven. Start the power and follow the on screen instructions. You should place the pen’s battery into the microwave and activate the setting. You need to then wait approximately 30 seconds before turning it back off. When you initially put the pen in to the microwave the electronic reading will show a low voltage protection setting. If this setting will not automatically get set you then should follow the on screen instructions.

After the Smok Pen has reached the temperature that it needs to reach you need to then connect both wires to the negative and positive on the positive post on the Smok unit. You should then connect another end of the battery to the negative post on the negative side of the Smok unit. The ultimate step is to connect the positive cable to underneath of the Smok’s power switch.

After all of the components have been placed in to the pen, you should turn the energy on. Following the first test run, you ought to be able to start to see the battery life indicator light seriously. If you do not see any sign of life from the Smok Pen, you need to remove the battery from the pen and replace it with a fresh one. For your convenience gleam green light that can be pressed so as to confirm the battery charging status. Once you have done these things and you also do not start to see the green light indicating charging, you need to replace the battery.

allen145

Website: